f52f cym 23/05/09-11:02:36
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x1
CH0 RX Vref:26.7%, TX Vref:18.8%,19.8%
CH1 RX Vref:26.7%, TX Vref:21.8%,20.8%
CH2 RX Vref:26.7%, TX Vref:18.8%,19.8%
CH3 RX Vref:27.9%, TX Vref:18.8%,19.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Jun 06 2024 - 00:53:05)
unrecognized JEDEC id bytes: 00, 00, 00
unknown raw ID 0 0 0
Trying to boot from MMC2
spl: partition error
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(7efcd01a0f...) + OK
## Checking uboot 0x00200000 ... sha256(e6e0a52a63...) + OK
## Checking fdt 0x0031f058 ... sha256(a4fd4b8eff...) + OK
## Checking atf-2 0x000f0000 ... sha256(da90adf3a4...) + OK
## Checking atf-3 0xff100000 ... sha256(1163474a5b...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 203.297/425.972 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-589-g3389cfdda:derrick.huang
NOTICE:  BL31: Built : 10:14:29, May  9 2023
INFO:    spec: 0x13
INFO:    ext 32k is valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-armbian (Jun 06 2024 - 00:53:05 +0000)

Model: NanoPi R6S
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM:  8 GiB
Sysmem: init
Relocation Offset: eda3e000
Relocation fdt: eb9f9d20 - eb9fecc8
CR: M/C/I
Using default environment

optee check api revision fail: -1.0
optee api revision is too low
### ERROR ### Please RESET the board ###